Home > : Transportation Assemblies

Transportation Assemblies




Transportation Assemblies		 Transportation Assemblies

From test stands and proving grounds to general on-vehicle monitoring, the GE Sensing product portfolio enables precision measurement of many safety and performance critical temperature parameters under diverse and often extreme operating conditions.


Product RoHS compliance status >>




       
Product Spotlight
Type KY2, KY3 Type KY2, KY3
Composite thermistor types KY2 and KY3 contain one PTC and two NTC thermistor elements connected inside a plastic sleeve and encapsulated in a brass probe housing. This thermistor type is primarily intended for automotive applications.

 
Type Active Incar Sensor/Type Ambient Hose Sensor Type Active Incar Sensor/Type Ambient Hose Sensor
This sensor indicates the cabin temperature of the fully automated temperature control system in the passenger car. It provides steady air flow through the hose, high sensitivity and delivers a more accurate signal to the fully automated temperature control system.

 
 
Type NTC Disc / Washers NTC Unleaded Disc Thermistors
Typical applications include automotive engine temperature gauge driving.
 
   
 
Type UD20 thermistor disc NTC Thermistors Type KU Unleaded Disc
A range of unleaded disc thermistors.
 
   
 
Type Air Quality Sensor Air Quality Sensor
The Air Quality Sensor (AQS) monitors the air coming into the vehicle for exhaust gas and sends a signal to open or close the damper to help maintain good air quality inside the vehicle.
 
   
 
Type Dual Solar Sensor Dual Solar Sensor
Dual solar sensor is mounted on the IP panel near the front window. The dual solar sensor uses two photo diode cells inside of it to measure the intensity of the light that enters into the cabin of the vehicle. It then takes this information and fees it back to the automatic temperature control (ATC) unit of the vehicle's air conditioning system. The air temperatures of the driver's side and passenger side are then automatically adjusted up or down depending upon the amount of light entering both sides of the vehicle.
 
   
 
Type Oil Pressure Switch Oil Pressure Switch
The Oil pressure switch monitors the engine oil flow when the engine starts. It can detect oil pressure and enables the EMS ECU to check for the lack of oil. It can also send an alarm signal to the driver, helping to avoid engine damage due to overheating.
 
   
   
Product Spotlight
 
Type Incar Sensor/Type Ambient Hose Sensor Type Incar Sensor/Type Ambient Hose Sensor
This sensor indicates the cabin temperature of the fully automated temperature control system in the passenger car. It provides steady air flow through the hose, high sensitivity and delivers a more accurate signal to the fully automated temperature control system.
 
   
 
Type Duct Air Sensor Duct Sensor
This sensor measures the temperature of air conditioner systems.
 
   
 
  Type S/AS/ES
Thermometrics temperature standards consist of ultra-stable thermistor probes assembled into thin wall stainless steel housings with shielded extension leads.
 
   
 
Type Ambient Sensor Ambient Sensor
This sensor measures the temperature outside the passenger compartment and is usually mounted inside or near the front bumper. The sensor provides input to automatic HVAC systems to help control the interior temperature of the automobile. The sensor also provides the vehicle occupants with temperature readings from outside the car. This information is particularly useful when driving under near freezing or freezing conditions.
 
   
 
Type UD20 thermistor disc NTC Thermistors Type UD20 Unleaded Disc
Unleaded disc thermistor for engine temperature measurement.
 
   
 
Type E-Stat Controller E-stat Controller
The E-stat controller is used to prevent the evaporator core from freezing. The NTC probe senses the temperature of the air as it passes through the evaporator core.
 
   
 
Type Water Temperature Sensor Water Temperature Sensor
The Water temperature sensor indicates the ambient temperature of the automatic air conditioner system in the passenger car. It provides high sensitivity and delivers a more accurate signal to the automatic air conditioner system, which allows for better temperature control of the HVAC system.
 
   
 
Type Single Solar Sensor Single Solar Sensor
Single solar sensors are mounted on the IP panel near the front window. The single solar sensor has one photo diode cell inside and is used in the independent type ATC, by sensing the amount of light left to right, using angle light activating filters. The sensor uses the amount of outside sunlight coming into the vehicle to help control the vehicle’s HVAC system.